Plastic Machining Tools
As only supplier on the market, we offer a special tool system for machining plastics as standard tools from stock. This unique system offers many advantages for machining plastics compared to convenient tools.

Als einziger Anbieter auf dem Markt haben wir ein spezielles Werkzeugsystem für die Zerspanung von Kunststoffen als Standardwerkzeuge ab Lager im Programm. Dieses einzigartige System bietet gegenüber konventionellen Werkzeugen viele Vorteile bei der Kunststoffbearbeitung und der Herstellung von Kunststoffdrehteilen.
Grooving and Cutting off Tools
Extremely sharp cutting edges, very good chip control and custom-made blade and cutting geometries. Our tool systems master the challenges posed by the machining of plastics (polymers). No matter with of without chips.
Copy Turning
Special indexable turning inserts and suitable holders tailored precisely to the needs of plastic processing. Suitable for many plastics in cemented carbide and for fillers with PKD inserts.
All plastic machining tools in the PDF catalog (guide) for available download:
Parting off Systems
Extremely sharp cutting edges, very good chip control and custom-made blade and cutting geometries. Our tool systems master the challenges posed by the machining of plastics (polymers).
Cutting off Tools
Dieterle tools for chiples cutting work particularly well on soft plastics such as elastomers. The knife-like cutting geometries enable nearly burr-free separation of the workpieces from the stock with a fine blade.
Advantages of our plastic machining tools:
- Extremely sharp cutting edges
- Very good chip control
- Especially polished sections for thermosetting plastics, thermoplasts, elastomers, rubber, PTFE, etc. (e.g. to avoid burrs)
- Chiplessly parting off elastomers
- Individual design of the blade and cutting geometry possible
KBS-2-7
Tool holders in shank sizes from 8x8 mm,
cutting width up to 2 mm,
insert heigt up to 7 mm,
cutting depth up to 10 mm
Large selection of standard indexable inserts from stock!
KBS-2-9
Tool holders in shank sizes from 10x10 mm,
cutting width up to 2 mm,
insert heigt up to 9 mm,
cutting depth up to 18 mm
Large selection of standard indexable inserts from stock!
Chipless Cutting with the KBS System
Machining: Chipless cutting witht KP-2-9-RX-A-UFK2
Material: Polyurethane
Workpiece: Sealing washers
Tooth geometry: RX
- Extremely sharp cutting edges enable chipless cutting of elastomers
- Little heat development and no sticking of the material
- Very good surfaces on the workpieces
The following indexable insert types are available for chipless cutting with the KBS system:
KP-VG
Dieterle VG cutting inserts is the basic form for chipless processing. The polished cutting-off blade is super sharp. This allows it to glide quickly and with low heat generation through soft plastics.
KP-12°
The entire chamfer concentrates on the cutting point of the Dieterle 12° cutting inserts. All polished facets converge to this extremely sharp point, through which soft plastics offer almost no resistance.
SDAC-KP
Höchst positive Wendeschneidplatten zum Kopierdrehen - optimal zum Kugelformdrehen - mit Grundform 7,5°
KP-VCGT-11
Höchst positive Wendeschneidplatten zum Kopierdrehen - optimal zum Kugelformdrehen - mit Grundform 35°
SDAC-KP-90
Die neuen KP-VCGT Wechselschneidplatten wurden speziell zum Einstechen, Langdrehen und Kopierdrehen von Kunststoffen entwickelt. Ihre hoch-positive und umfanggeschliffene Geometrie mit poliertem Spanwinkel garantiert einen sehr aggressiven und dennoch weichen Schnitt. Durch ihre schlanke Geometrie sind diese Wechselschneidplatten optimal geeignet um feinste Konturen auch hinter Bund zu realisieren.
Die neuen KP-VCGT Wechselschneidplatten sind erhältlich in den Größen VCGT-0702.. und VCGT-1303.. mit R0,2 sowie R0,4. Eine Stechtiefe bis zu 5,5 mm ist realisierbar. Der passende Werkzeughalter SDAC-KP-90.. gewährleistet eine Drehbearbeitung mit einem Winkel von 90° zur Drehachse. Der Werkzeughalter SDAC-KP-90 ist in den üblichen Halterquerschnitten verfügbar.
Spanabhebende Kunststoffbearbeitung
mit dem System KP-VCGT
Bearbeitung: Ansatz Andrehen mit KP-VCGT-11-S-K10, Spanloses Abschneiden mit KP-2-7-12°-12-B-UFK2
Material: Teflon
Werkstück: Dichtungsscheiben
- Umfanggeschliffene Wendeschneidplatten mit polierter Spanleitstufe
- Gute Spanabfuhr mit wenig Wärmeentwicklung
- Sehr gute Oberflächen an den Werkstücken
Für die spanabhebende Kunststoffbearbeitung mit dem System KP-VCGT stehen folgende Wendeschneidplatten-Typen zur Verfügung:
KP-VCGT-07 + KP-VCGT-13
KP-VCGT-07 l tmax 2,8mm
SDAC-KP-90-07 holder
KP-VCGT-13 l tmax 5,5mm
SDAC-KP-90-13 holder
ISO-Indexable Inserts
Our selection of ISO turning inserts tailored for plastic processing for precise copy turning. Efficient solutions through outstanding sharpness.
Depending on the application areas, plastics are reinforced with glass or carbon fibers (GFR/ CFR) to improve mechanical properties. For the machining of these plastics, we recommend our indexable inserts with PCD tooling.
Special Tools for Machining Plastics
In addition to our standard tools for machining plastics, we can realise a large number of special tools for you according to your individual requirements. With our special tools for machining plastics, bellows, special seals and many other plastic turned parts can be manufactured precisely and efficiently. We are happy to help!